Solutions to common problems of CNC special-shaped edging machines

The CNC special-shaped edging machine should roughen the edge and smooth the edge. For customers, it is the basic rule that the trimming is smoother and jagged, and the flatness of the edge should be within /-0.4mm, considering the reasons for this difficulty:

1. In the CNC special-shaped edging machine, the four wheel sets have different cutting energy. Especially when looking at the last set of quads, the edge and straightness can get rough.

2. Differences between contemporaneous and pressure belts, too loose pressure beams are all factors that lead to flat edges.

3. The excess cutting energy of the blank holder will cause serious damage to the grinder and make the blank holder not smooth. In this case, turn off the edge wheel and polish it again. In more serious cases, shut down the machine for adjustment.

The circle is not uniform. The circle is generally between 0.7mm and 1.3mm. When it is greater than 1.3mm, it is a circle width, and when it is less than 0.7mm, it is a circle. If you have problems with rounded corners, you can make the following adjustments:

1. Confirm that the pre-grinding fillet is too large to eliminate post-grinding.

2. Due to the back grinding, there is an error in the adjustment of the straight hair splint, resulting in eccentric grinding, one side is more polished, and the other side is less polished, resulting in rounded width and non-rounded corners.

3. After the new rounded four wheels are replaced, the width of the rounded corners is caused by the excessive standard air pressure.

4. The vision of the pneumatic components is not adjusted in time, causing some rounded corners to become larger or rounded.

Bumpers, missing edges, bumpers often have small bumpers, round bumpers, and large bumpers. It is usually caused by the untimely adjustment of the four wheels. The fillet clinker is in front of the blank because the fillet is reduced too quickly. The large impact ceramics on the rounded corners are usually caused by the loosening of the four-wheel screws, the reverse rotation of the four-wheel motor, and the skewed viewing angle of the four-wheel.

Insufficient clams and front angle: The main reason is that the moving angle of the grinding disc bracket is small, so generally 2-3 mm is an effective category, the rear tire is worn or the diamond sand of the grinding disc wheel is too coarse and rotten. Insufficient rake angle is mainly due to too many grinding heads or some of the grinding heads are not sharp enough.

Relief corners, serrations and lack of burrs are mainly due to over-sanded parts of the 5th and 7th sets of edges, collapsed rear corners, too much bristles, and too few side wheels. The effect would be better if the puck was made rougher. Then the yardage is less, so reduce the grind by 5 and 7 sets.

CNC special-shaped edging machine solution

The pressure roller of the CNC special-shaped edging machine prevents the uneven surface of the floor tile surface.

Solution: The working pressure of the pressure roller is uneven, and there is a gap between the pressure roller and the floor tile surface. Check the rollers for damage, then make tight adjustments to the rollers and tile surfaces.

Directional deviation of conveyor belt of CNC special-shaped edging machine

Solution: The direction of the conveyor belt of the drive shaft is twisted, and there are two compensation device wheels directly under the conveyor belt of the drive shaft. After the conveyor belt is detached from the side of the appliance control box, loosen the tightening nut near the control box, move the adjusting roller bearing down, and then tighten the screw. If offset to the other side, the roller bearing on the other side can move up. Tile wheat blank production and processing conditions appear!

Solution: The speed ratio of the variable frequency motor is too fast. If it is too fast, the production and processing will loosen due to the different production and processing speeds of the transmission belt and floor tiles. When the motor is no-load, the floor tiles do not pass, or the floor tiles are not finished production and processing, and the work speed is too fast. Adjust the speed ratios of possible variable frequency motors and adjust according to the statistics provided by the manufacturer.

The motor of CNC special-shaped edging machine is interlocked or stopped to be fixed or fixed!